If the Advanced Audio High-Output Amplifier is installed under the Tour-Pak: Grasp the tie strap (7) on the end of the Vinyl spring sleeve (8), and use a tie strap from the kit to fasten the end of the spring to the lower left slot on the license plate holder. If stronger headset receptacle retention is desired, the spring assembly in the kit can be replaced with spring assembly 76300-06 (purchased separately). The rider's safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation.... the Parts and Accessories section of www.harley-davidson.com. (English .... Obtain the speaker switch adapter wire (purchased separately or ...

Oct 7, 2010 ... the Parts and Accessories section of www.harley-davidson.com. (English only). ... 4. See Figure 2. Install the gear indicator (2) with the wires ...Slide the wedge (3) with the pointed ends between the two boxes on the back of the gear indicator (2) from the tab side of the bracket (1). The wedge pointed ends are different thicknesses and have to conform to the step of the housing plate surface. This will secure the gear indicator tightly to the mounting bracket surface....

FX-series Big Twin and XL-series Sportster models prior to 1984, FL-series Big Twin models prior to 1985 and all models with OE points will require OE timing rotor PN 32402-83. This part is not included with the MSD V-Series Ignition. It can be purchased from your local Harley-Davidson® dealer. It is recommended to have the Service Manual for your motorcycle. WARNING: When installing the MSD, disconnect the battery cables. When disconnecting, always remove the negative cable first and re-install it last. Note: Do not discard the nose cone cover, timing plate screws or washers as they will be used with your new ignition....Wire Ties. MSD V-SeriesTM Ignition for Harley-Davidson®. PN 4226. Harley- Davidson® is a Registered Trademark of Harley-Davidson. WIRING. RED ...

Harley-. DaviDson. Heated Grips. Install the switch housing mounting hardware. Align the glue-less grip into the switch housing. 9. Attach the grip wiring to the ...The grips remain at a constant temperature regardless of changes in outside temperatures. The self-contained control circuit and control knob means you have no additional switches or controller boxes to mount, and the grips are switched on/off with the ignition to avoid draining your battery. The “glue-less” grip design allows grip removal if you change handlebars or motorcycles. Original equipment on the FLHTK Ultra Limited™ model, these Black Rubber Heated Grips feature smooth surfaces and a clean design that complements any styling direction....

K380IN KAWASAKI VULCAN. 1500 LONGSHOT. EXHAUST SYSTEM. Part #18387. CONGRATULATIONS! You have purchased the finest ...REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece...

Kawasaki Vulcan 1700 Nomad and Voyager. Will not fit the Vulcan 1700 Classic. Ultimate seats Installation. Install Kit. Nylon washer spacers = 4 pcs...Removal of Stock Seats 1. Release the passenger seat with the key lock located in the side cover on the clutch side of the bike. 2. Lift passenger seat up and forward to remove. 3. Remove the rider seat by lifting the back and sliding it back. 4. Remove the latch plate from the stock passenger seat base and install it onto your new Ultimate passenger seat using the same nuts....

REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. Note: Save the header flange, it will be reused upon installation...Page 1 of 2. K290IN Rev 3.1. KAWASAKI. VULCAN 1500 2 into 2. EXHAUST SYSTEM. Part #'s 18301, 18361, 18371 &. 19361. CONGRATULATIONS!

BIG AIR KIT - Kawasaki Vulcan 1500/1600 EFI Models. CAUTION! We Strongly recommend that a qualified technician install this kit if you do not completely ...*Remove screws holding backing plate to the cross-over tube. (D on Fig. 1) *Remove remaining screws and pull backing plate from throttle body, pushing the hose out as you go. *Remove crankcase vent from rear of the backing plate. (D on Fig 2) *Disconnect electrical connection to the valves. (B on Fig 1 and C on Fig 2) *Remove Inlet Air Temperature Sensor from backing plate. (B on Fig 2)...

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM...REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber....Page 1 of 2. K390IN Rev 1.0. KAWASAKI VULCAN. 1500 PRO PIPE HS. EXHAUST SYSTEM. Part #'s 25301. CONGRATULATIONS! You have purchased the ...

Stainless Steel- All metal sales crop is one of the top suppliers of stainless steel sheet, plate stainless steel coil, stainless steel strip and bar. We are your direct mill source and warehouse provider.