This body lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in a collision or misused. Off road use of your vehicle with this body lift installed may increase the stress applied to the factory body mounts. We do not recommend that any vehicle with a body lift installed be involved in any extreme off road maneuvers such as jumping

If you do not have a tow hitch or tow hook, proceed to Step 2. If your vehicle is equipped with a tow hitch or tow hook, you will need to remove it before you remove the factory bumper. To remove a tow hitch, use a wrench with an 18mm socket to remove the four (4) bolts that secure it to the bumper and discard them. If you have a tow hook, use a wrench with an 18mm socket to remove the three (3) bolts that mount it to the bumper and discard them.

ARB DELUXE WINCH BARS Including Air Bag Equipped Models Year Type Features 2007-08 Winch Bumper Air Bag Approved, Retains the Factory Fog Lift Jack Points, Auxiliary Light Mount Provisions

The Jeep Wrangler was redesigned for 2007 (see Figure 1). The changes, especially the new features of the frame, are indicative of other vehicle maker trends in body-over-frame design. These include closed rail construction, hydroforming, less use of rivets, and crush zones in the frame rails similar to unibody construction. This article provides a collision repair overview of the 2007 Jeep Wrangler, starting with the redesigned frame. strength in the roll-formed center section (see Figure 2). High-strength steel internal reinforcements in selected areas in the frame are all 50,000 psi minimum yield strength

Remove ignition key and put the vehicle in park or in gear to prevent others from starting the vehicle during installation or service. • Wear only snug-fitting clothing while working on your vehicle or snowplow. • Do not wear jewelry or a necktie, and secure long hair.

Bolt Torque Specifications Torque Specifications c Torque in Foot-Pounds for Metric Bolts e in Foot Pounds Metric et Bolt Size Grade 8 8 Grade 10 9 t Size G ade 8. Gr d 10.9 i Grad 8.8 Grade Grade a rad 6MM 6MM 6 8 8MM 16 22 8MM 10MM 10MM 0M 0 31 40 12MM MM 70 54 70 14MM 89 117 Confirm the towability and pre-towing procedures for your vehicle with the owner’s manual or contact the vehicle’s manufacturer for specific towing procedures.

1. Remove the driver side lower bumper bolt (bolt #1) also remove lower steering box mounting bolt (bolt #2) from frame as shown in figure #1. 2. Holding the skid plate in place, placing the three holes in the skid plate over the existing holes in frame. 3. With the skid plate in place, replace the bumper bolt (bolt #1) and steering box bolt (bolt #2). 4. Use the existing hole in the frame (A) to line up the rear skid plate bolt.Put the nut inside the frame. 5. Put the 5/8" aluminum spacer in place, shim accordingly with supplied washers and install the 3/8" x 2" bolt (bolt #3).

Hardware Kit for JK Winch Mount Plate - 2007 Jeep JK* - all models with front Body Armor Bumper DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN JEEP JK* MODELS. Body Armor designed this product to give you years of dependability and performance. If you encounter any problems during installation of this product, or at any later date, please contact your authorized Body Armor dealer, or call 951-808-0750 for our customer service department, or check our website for tech bulletins regarding your year and model vehicle. Our hours are Monday thru Thursday 7AM-4:30PM and Friday 8AM-12PM, Pacific Time

1. Remove existing bolt from bumper attachment on driver and passenger side. 2. Remove tow hooks if equipped. Return hooks and hardware to vehicle owner. 3. Raise hitch into position and secure with hardware as shown. Hardware attaching to weldnut from Step 1 will vary by vehicle. Use either 7/16" bolt and 7/16" conical toothed washer, or M12 bolt and 1/2" conical toothed washer.

All product illustrations and specifications are based upon current information at the time of publication approval. Although descriptions are believed correct, accuracy cannot be guaranteed. DaimlerChrysler reserves the right to make changes from time to time without notice or obligation, in prices, specifications, colours and materials, and to change or discontinue models